If in your washing machine If the Samsung heating element (heating element) is broken, you can tell by the remaining dirty laundry. The machine simply cannot wash things in cold water.
You can also determine this failure yourself by the HE or TE error on the control module.
This error may indicate a malfunction of either the heating element itself or the water temperature sensor (thermistor). In this case, the wash program will be stopped because the water is not heated to the required temperature.
In general, there are few reasons for the malfunction:
- The heating element burned out;
- the temperature sensor (thermistor) has failed;
- problems in the control module (which generally does not often happen with such an error).
If a failure occurs during washing, do not forget to drain the water from the tank and remove the items before further disassembling the machine! The water drain valve is located at the bottom of the machine on the right under the false panel.
Determining where the heating element is located
So, first we need to determine where the heating element is located in the Samsung washing machine.
Please note that on Samsung the heating element can be located both in the front and in the back. And since back cover It's much easier to remove - it's just a few unscrewed screws, so it makes sense to start with the back cover.
For example, on washing machines Samsung Diamond with a load of up to 5 kg, the heating element is located exactly at the back. But on Samsung models Fuzzy, such as S821 and S621, the heating element is located at the front.
Advice: do not rush to buy a new heating element even before disassembling the machine; first diagnose the breakdown. Perhaps the problem is not in the heating element, but in the temperature sensor.
How to remove the front panel
In any case, we start by removing the top cover of the washing machine. Unscrew the two screws on the back under the cover. Slide the cover to the back and remove.
If, after removing the top cover, it is not possible to visually determine on which side of the machine the heating element is installed, then remove the back cover.
If there is no heating element behind the machine, or if it was possible to determine from above that the heating element is located in front of the Samsung washing machine, then we follow the steps:
1. Take out the powder dispenser hopper and unscrew the two screws, as well as the screw on the right side of the control panel.
2. Unfasten the lower false panel.
3. Unscrew the lower fastening of the front panel.
4. Lifting the control panel, unscrew the screws securing the front panel.
5. Remove the outer collar of the hatch cuff by hooking it with a slotted screwdriver near the hinge of the hatch door.
6. Unscrew the hatch lock mount (you can leave it, but then be careful with the lock wires when removing the front panel).
7. Remove the front panel
Below in front of you is a heating element.
How to check the heating element
After you have removed the front panel, you need to determine the cause of the problem. First of all, we diagnose the heating element itself with a multimeter. Diagnostics can be carried out without removing the heating element.
Turn on the multimeter and check its functionality by closing the contacts. Next, we place one probe on one contact of the heating element, the second probe on another contact.
The resistance of the working heating element on a Samsung washing machine is 45-69 Ohms, depending on its power. And the power of the heating element on Samsung can be from 800 to 2000 W. If the multimeter shows a value of 0 or 1, the heating element is faulty and must be replaced.
If the value on the multimeter is 0, the sensor needs to be replaced.
How to remove the heating element
To remove the heating element from a Samsung washing machine, you need to perform three operations:
- Unscrew the central nut (not all the way);
- Press on it (you can use the handle of a hammer);
- Using a screwdriver, carefully pry the heating element around the perimeter and remove it, having first removed the wires from the terminals and from the temperature sensor.
Replacing the heating element
Replacing the heating element of a Samsung washing machine with your own hands is not such a difficult task. Before installing a new heating element, we also check its performance with a multimeter. Don't forget to drop a little machine oil on the rubber seal of the new heating element at its junction, this will speed up its installation.
Before installing a new heating element, do not forget to clear the bottom of the tank of debris. This can be done just through the hole for installing the heating element.
We install a new heating element, connect all the wires and the temperature sensor connector. We assemble the washing machine panels in the reverse order and check its functionality after assembly.
A washing machine is an indispensable electrical appliance that is used quite often, as a result of which the device may periodically require repair. The causes of breakdowns can be different, the quality of water plays a big role, its increased hardness can lead to malfunctions of the heating element.
Why do you need a heating element?
An ordinary tubular electric heater (TEH) is responsible for heating the water in the machine; it is found in all models of washing machines, it can be LG, Samsung or any other brand. It is made in the form of a metal tube, the ten can have different shapes, when passing through it, electrical energy is converted into heat, as a result the water heats up.
Signs of a heating element malfunction
A specialist can calculate almost any malfunction even without diagnostics; a heating element malfunction is most often accompanied by the following symptoms:
- The machine does not heat the water - to check, just touch the hatch through which the laundry is loaded. washing in this case becomes impossible; programs can still be executed in standard mode, in modern models, information about the heating error is displayed on the display;
- The machine is knocked out immediately after starting or after 8-12 minutes. after turning on the heating - this often occurs when the coil in the heater is short-circuited;
- the machine knocks out the RCD after switching on or during the process of heating water, this situation is typical for a short circuit of the heating element to the body or a leak electric current on the body due to poor insulation;
- continuous washing over a long period of time.
The listed signs are considered indirect; the technician has the right to change the heating element after checking the device with a multimeter. Replacing the heater does not take much time, the procedure takes no more than 30-40 minutes, less for professional technicians.
The process of replacing the heating element
Before carrying out repairs, the water from the machine must first be drained and disconnected from the network, the sequence of actions when repairing devices different manufacturers practically no different; when disassembling, the cover can be removed from the back or front. When the heating element is located at the rear, the water supply and drain pipe are disconnected. In standard mode, replacing the heating element of a washing machine is carried out in several stages; if necessary, you can read the instructions.
If your lg washing machine can no longer cope with stains on clothes, most likely it washes it in cold water, which means that the equipment is faulty; it is responsible for heating, so the failure of this part leads to very sad consequences and inevitable repairs . In most cases, the heating element has to be changed, and to do this you need to somehow get to it. This review is dedicated to this very question, how to remove the heating element from an LG washing machine.
The first step is to figure out what could be causing the heater to malfunction.
Possible causes of tena failure:
- Wiring, open circuit;
- Presence of scale, increased level of water hardness;
- Sudden voltage drop;
These are the main and most common reasons that lead to the inoperability of the LG washing machine. In such cases, the owner of the equipment needs to contact the LG equipment repair service; competent specialists will cope with any task as quickly as possible and will charge more than a modest fee for it.
Circuit break
The electrical wiring of a washing machine is subject to wear and tear; in addition, depending on the design of the equipment itself, the wires may be rubbed in by the drum, which will lead to their rupture or damage; in both cases, the ten will fail and without reaching it it will be impossible to determine the real cause of the malfunction. Naturally, a damaged wire must be repaired or even replaced; in essence, such work does not take much time for a technician; it will take much longer to disassemble the car to get to the ten.
Poor quality water
The problem is very urgent, scale and hard water will quickly damage the heater, and in this case it will have to be replaced, since this part usually cannot be repaired. Using anti-scale products can correct the situation, but only if they are used from the moment you purchase the equipment; if the heater is no longer working, it is useless.
Voltage drops
A sharp surge in voltage during the washing process can lead to the heater simply burning out, then in any case the owner will have a question about how to change the lg heater in the washing machine, and most importantly, can you do it yourself? The answer is obvious, without special skills and appropriate education, it is impossible, and besides, you will need a certain tool. Again we come to the conclusion that we cannot do without the help of qualified LG service specialists.
This outcome can be avoided; to do this, it is advisable to install a separate outlet for the machine, which will be powered from an individual differential machine.
How to change the tenon in a washing machineLG
First of all, the shadow needs to be removed, and this is not an easy task, let’s move on to analyzing this process.
- Disassembling the washing machine body;
- Remove the drive belt;
- Disconnect the terminals from the ten;
- Remove the positive terminal of the temperature sensor;
- Loosen the nut a few turns and push the bolt in;
- Remove the tensile using flat screwdrivers;
- Carefully remove the part from the washing machine without damaging the tank;
Removing parts of the machine body
First of all, to find out how to remove the screen in the LG washing machine, you need to get rid of the back cover of the case, this way you can gain access to all the parts of the device. Depending on the model of the machine, the cover may be secured with a different number of bolts, but in any case it will not be difficult to remove, so anyone can handle this task with a screwdriver or cordless drill.
Drive belt
The location of the drum drive belt limits access to the ten, so it is better to remove it during work. The process is also not complicated, just pry the belt with a screwdriver and release it. The main thing in this process is not to damage the belt itself, otherwise there is a risk that it will break during further use.
Power and temperature sensor terminals
The next step is to remove all the terminals, just disconnect them from the ten and put them aside. There are usually four terminals in total, these are the terminals of the power cables, grounding and the positive wire of the temperature sensor, which, by the way, may not exist, again depends on specific model. Do not forget to turn off the power to the machine before starting work to avoid unpleasant situations.
Removing the shade
Now you know how to remove the heater from the LG washing machine, all that remains is to loosen the central nut of the part and push the bolt holding the heater inside, after which you can start removing it. The sealing rubber bands are extremely reliable, so removing the part will not be so easy, the main thing is to do everything as carefully as possible, in order to avoid damage to the equipment itself. Once everything is ready, you can begin installing a new tena.
How to replace the ten on a washing machinelg
The best option would be to install exactly the same new one, or at least an analogue one, in place of the old tena, but in any case it must match in size, this is a prerequisite.
What tool will you need:
- The first thing you need to do is stock up on lubricant; you can use any available technical product that is available.
- In addition, you will need a wrench with an eight-socket head.
- A set of screwdrivers, you need a flathead and a Phillips.
- A multimeter will also be useful.
How to change in a washing machinelgten
In general, the process of installing a new heater is not that complicated, but if you are not confident in your abilities, it is best to use the services of a specialist, the LG service center provides a full range of repair and maintenance services for the manufacturer’s equipment, including washing machines.
To begin with, take the lubricant that you prepared in advance, you need to generously lubricate the elastic band of the ten, after which you can put it in place. Once this is done, place the previously unscrewed nut on the bolt and tighten securely with a wrench. Install all terminals in place, most importantly in the same order in which they were removed, in order to achieve stable and uninterrupted operation of the device. If everything is done correctly, you can assemble the machine body and connect it to the network, checking the functionality of the equipment, everything should function.
TEN (tubular electric heater) is functional element washing machine, responsible for heating the water during washing. It is a tube with a conductive thread inside, while the tube itself is filled with a heat-conducting insulator (dielectric). Over time, the part wears out and the user is faced with the question of replacing the heating element.
To carry out such repairs, it is important to know:
- where is the heating element located;
- what are the signs of a malfunction;
- how to change heating elements at home.
Having answered these questions, you can safely begin repairs and count on a positive result.
How to determine where the heater is located
The heating element is located at the bottom of the tank. Depending on the manufacturer of the equipment, the heating element may be located in the front or rear of the housing. Majority brands, such as Candy, Indesit, Zanussi, Ariston, Electrolux, Atlant, provide access to the heater through the back panel of the washing machine. Companies Samsung, Bosch, LG place heating elements in the front part, under the drum.
To determine the location of the part, you need to look at the size of the back panel of the machine. If there is a large removable surface at the back, then the heating element is most likely located there. If only a small cover can be unscrewed on the rear panel, then the exit to the heating element should be sought through the front panel. It is not always possible to determine the location of a part by external signs, so it is best to start looking for the location from the back - it is easier to remove it and screw it in place.
Signs of a malfunctioning heating element in a washing machine
A washing machine of any brand, be it Indesit, Ariston or Bosch, always gives signals that the heating element is broken. The main signs of a heater malfunction:
- The water does not heat up during the washing process. If the water remains cold when you start a high-temperature wash cycle, the heating element is not functioning. When the washing process reaches the stage of heating the water, the machine stops working and displays an error. At the same time, programs that do not require heating water can operate as usual.
- Before heating the water, the equipment “knocks out the machine” - turns off the device, which protects the electrical lines coming after it from combustion. The failure occurs approximately 10-12 minutes after starting the washing program. Most often, this indicates a short circuit in the spiral, which is located inside the heating element.
- The machine “knocks out” the device protective shutdown(RCD). Trouble happens immediately after turning on the equipment or immediately before heating the water. Poor quality insulation of the heating element can cause current to enter the housing and lead to automatic shutdown RCD.
If one or more signs of failure are observed in the operation of the machine, the heater may be faulty and requires replacement. A test with a special device - a multimeter - allows you to accurately determine the performance of the heating element, after which you can be sure of the malfunction and begin replacing the heater.
How to replace the heating element
Before starting repairs, you need to completely drain the water from the machine and disconnect it from the mains. To carry out the work, you must have a screwdriver and an 8 or 10 inch wrench on hand. After this, you can start replacing.
First you need to determine the location of the heating element. Where the heating element can be located depending on the model and structural features of the washing machine is described above. Having reached the water heating system, the user will see only the outer part of the heating element - the terminals and wires, which must be disconnected before removing the heating element.
To get the heater you need to:
- unscrew the central nut using a socket wrench;
- using a screwdriver, insert the bolt into which the nut was screwed;
- Carefully pick up the heating element with a screwdriver and smoothly loosen it up and down and remove it from the rubber seal.
The faulty part should be repaired or replaced with a new one. When purchasing a new heater, you should know the exact markings of the previous one.
It is important to install the working heater in its place, ensuring an accurate and tight fit of the element. When the heater is installed, tighten the nut and connect the wires to the terminals.
Without closing the wall, check the operation of the heating element. To do this, you need to run a washing program with water heating at least +60 ℃ and after 10-15 minutes touch the loading hatch window. If it is warm, it means the water is heating up and the heating element is properly performing its function. After this, you can install the panel in place.
A breakdown of the heating element in any washing machine, including the Indesit brand, is detected immediately. After the first wash with a broken heating element, you will see that the laundry is dirty because it was washed in cold water.
In modern machines, the washing process may not start at all if a part is broken. What to do in case of such a malfunction? It’s simple - replace the heating element with a new one yourself, according to the instructions.
Where is the heating element located?
Replacing heating elements in Indesit brand washing machines is quite simple if you know how to hold a screwdriver and use a multimeter. In different cars you have to get to it in different ways when disassembling the equipment. Italian manufacturers took care of their consumers and installed the heating element in such a way that it can be reached by opening the back cover of the machine.
That is why such repairs are considered simple. The only drawback is that the washing machine is disconnected from all communications. This is necessary in order to turn the machine around at the back for repair work.
What is needed for replacement
Replacing the heating element with washing machine Indesit will require a minimum of tools from you; as a rule, two screwdrivers are enough: flat and figured and a wrench with a head. You also need a multimeter or tester to check the functionality of the heating element. And, of course, original spare parts.
Important! Do not buy spare parts made in China, you will not save money on this, you will only spend extra money, and soon you will have to replace the heating element again.
An original Italian-made heating element, depending on the model of the washing machine, costs from 700 to 1000 rubles, maybe a little more. It’s better to save on the work of a technician and try to remove and replace the heating element yourself. Of course, if the car is under warranty, then call a specialist service center, such repairs will be free.
Work order
And finally, we will describe the procedure for replacing the heating element.
So, as you can see, removing and replacing the heating element is not difficult. After replacement, check the functionality of the equipment. Good luck!
