A washing machine is a complex household appliance that requires adherence to certain operating rules. It needs a water supply, a drainage system, and electricity. Overloading may damage the device. For such a machine, a special powder marked “Automatic” is required. The washing program must be selected according to the type of fabric. Only after all the nuances have been taken into account can you wash your clothes.
Show all
Preparing to start the washing machine
Before you launch automatic washing machine, you need to perform a few simple steps. It is best to find instructions for it, which describe in detail all the nuances from installation to daily operation.
Water supply
If there are no instructions for turning on and it is not known whether the machine is ready for use, you need to start by inspecting the hoses. Any washing machine there are two of them:
- 1. One supplies water to the device.
- 2. Another pours it down the drain after washing.
A hose coming out of the top of the back wall of the washing machine supplies water. It is connected to a cold water pipe. Often, a tap is placed near the insertion point of the hose for emergency shut-off of water in the event of a malfunction of the washing machine. Make sure it is open. If there are no marks on it, then just remember where it is. Subsequently, if after pressing the “start” button on the device, water does not flow into the tank, you will need to turn it (which means that before that it was in the “closed” position).
If the end of the water supply hose is not connected anywhere, look for a separate nipple on the cold water pipe that is covered with a cap. If available, turn off the water in the apartment (taps are installed next to water meters as standard), remove the plug from the nipple and connect the free end of the hose to the pipe.
After this, open the cold water supply tap to the apartment and check the connection for leaks.
It must be tightly screwed to keep water out, otherwise it will flood the neighbors below. If the pipes do not have an end for the washing machine hose, you will have to call specialists to connect it. It is not always possible to do this on your own.
Drain
Having dealt with the water supply, you need to inspect the drain hose. Its end should go into the sewer pipe. If a permanent connection is not made, lower the end of the hose into the bathtub or toilet. Included with the washing machine for such cases is a plastic curved plate that fits onto the end of the hose. Without it, the pressure of water draining from the machine will knock the light hose out of the tank.
Electricity
The last step of the preparatory stage will be to inspect the electrical cord, which should be free of damage, creases and exposed wires. After making sure that it does not pose a clear threat when used, plug it into an electrical outlet. Now you can start washing.
Luke
The most common washing machines are horizontal loading. In this case, the door is located on the front wall and looks like a porthole or round window.
In order to open the hatch, you need to lightly press its rim and release. The second option is to feel the tab on the right under the handle and, pressing on it, pull the lid towards you.
If there is no hatch on the front wall of the machine, then it is a top-loading washing machine. To load laundry, you need to open the top lid using the handle. Most often, such a hatch design is found in Bosch and Indesit.
It is easy to identify a washing machine with a small load. If the width of the machine does not exceed 40 cm, and the drum itself is 15 cm, you can wash no more than 3 kg of dirty laundry at a time. You need to put things in the drum in a straightened form, without compacting it. As soon as you run out of space, you must stop downloading.
After finishing, for machines with vertical loading, you need to latch the drum itself, and only then the lid. When closed correctly, a characteristic click of the lock will be heard.
Powder
After the laundry is loaded into the drum, you need to pour the washing powder into a special compartment. On machines with horizontal loading, this is a drawer with three compartments.
On top-loading units, the powder tray is located on the inside of the top cover.
If your laundry is heavily soiled, you should choose pre-wash modes. Then the powder is poured into the compartment marked A (on some models it is marked I). In all other modes, laundry detergent is poured into compartment B (or II, respectively).
In such machines you can only use a product marked “Automatic”. Excessive foaming of hand wash powder can cause damage to the device. If capsules are used as detergent, they must be loaded with the laundry. Washing gel can be poured directly into the drum or tray. The powder is poured only into a special compartment.
The amount of powder depends on the amount of laundry. It is calculated by weight: one tablespoon per 1 kg. For example, a set of bedding for a double bed weighs approximately 2000 grams.
Washing program
IN washing machines different manufacturers The washing programs have slightly different names, but perform approximately the same functions. Their main difference is that they are designed for different types of things and the process takes place at different temperatures. Most often, programs are indicated around touch buttons, launching them.
or around a round wheel with a mark, with which you can select desired mode washing.
In addition, there are often separate buttons for additional rinsing or spin speed. They can only be used before starting: you cannot change an already activated washing program.
Starting the washing machine
If everything is done correctly, you can turn on the washing machine. To do this, click on the "Start" button. It looks different, but the designation on it is the same and it is easy to recognize.
Washing machines from various manufacturers, be it Indesit or Zanussi, Samsung or Ardo, are easy and simple to operate. It shouldn’t be any other way, because this technique is intended for people of all ages: from elderly grandparents to young school-age children, who themselves can take care of the cleanliness of their clothes. If anyone else doesn’t know how to turn on a washing machine, join us!
- Connect the machine to the power supply.
- Prepare laundry for loading into the drum, taking into account the following rules:
- White and light-colored laundry must be washed separately from colored and dark ones.
- The amount of clothing to be loaded must correspond to the nominal value of your machine: you cannot fill the drum to capacity and put in a small amount of clothes.
- Wash items only from the same type of fabric at the same time.
Washing powder is loaded into a special powder tray, which has three compartments:
- the left compartment is for the main wash;
- right – for preliminary;
- medium - for air conditioning.
This distribution of compartments is typical for almost all brands of washing machines. On Zanussi machines, on the front panel of the tray there is a reminder about the purpose of its compartments. For other models, you can always check by looking at the user manual, which includes complete guide on driving the machine.
When adding powder, you should follow the dosage. It is usually indicated on the packaging.
Some are sure that the more powder, the higher the quality of washing. This is a misconception, leading to the fact that excess powder is poorly rinsed, and then becomes a source of allergic diseases.
Load the prepared items into the drum, laying them out so that they do not lie in a lump. This way, the process of washing and spinning clothes will be performed better. Close the car door tightly.
The operating mode is selected either by pressing the corresponding button or by rotating the switch whose arrow is directed to the selected mode. Some models, such as Zanussi, have both types of control.
The washing machine has different operating modes, depending on the type of fabric and washing intensity:
- cotton;
- synthetics;
- wool;
- everyday washing;
- quick wash;
- gentle wash;
- baby clothes.
Determining the washing temperature
Temperature conditions are set from 30 to 95 degrees. You should not always choose the maximum temperature, follow the recommendations:
- The temperature is selected depending on the degree of soiling of the laundry. If you just need to freshen it up, choose 30 or 40 degrees.
- Synthetic fabrics wash well at 40-60 degrees.
- Bedding and bath items should be washed at maximum temperature.
Selecting the spin intensity of the laundry
The spin intensity is set by the number of revolutions per minute. The better the spin, the less water remains in the laundry, and it will dry faster.
It is necessary to remember: for products made from delicate fabrics, the minimum intensity is selected. And for some particularly delicate fabrics, such as silk, chiffon, it is recommended to do without spinning.
The machine is turned on by pressing the “ON” button. The cycle is started by pressing the “START” button. When the wash starts, the indicator shows the time before it will end.
Important! Many modern models, such as Zanussi, have a delayed start option. This means that you yourself can determine when to turn on the machine by specifying a specific time.
If you prepare the machine with laundry, set the delayed start mode, setting the start, for example, at 5 o’clock in the morning, you can easily forget about it. The device can turn on at the appointed time and carry out the specified program. And all you need to do is take out your clean laundry in the morning.
Important! By doing laundry at night, you will significantly save on the difference between day and night electricity tariffs
End of cycle
At the end of the cycle, the machine will stop and a sound will sound. sound signal. After 30 seconds, the door lock will turn off and the washed items can be removed. If suddenly the door does not open, this may be the result of various breakdowns.
Use a dry cloth to wipe the drum and rubber cuff on the doorway. There is usually a lot of water left in the fold of the cuff. Bend it slightly and collect the water with a napkin.
The machine door should be left slightly open to dry, so that mold and fungi spores do not settle in it.
- Models from different manufacturers have different control panels. For some models, such as Indesit, Zanussi, you do not need to separately set the modes of individual stages of the cycle, but you can select a ready-made program that includes the specified parameters. For example, the “Cotton” program at a temperature of 90 degrees or the “Synthetics” program at a temperature of 60 degrees.
- Can only be used for washing special powders intended for automatic washing machines, but not for hand washing.
- Along with washing powders, you can use liquid products. They can be poured into the powder tray or directly into the drum when loading laundry. Modern Zanussi models have a partition in the tray for liquid detergents, thanks to which the washing liquid does not flow away immediately, but remains in the tray until the water is supplied. Read more about where to pour detergents and what types they are.
- For heavily soiled laundry, you can use the soak mode or prewash.
- What to do if you turn on the washing machine and it doesn’t work? Check whether there is cold water and whether its pressure in the water supply network is sufficient. A washing machine that is turned on and running will stop if the cold water supply suddenly stops.
- If, during the spin cycle, the laundry in the drum becomes crumpled, it will not be able to be evenly distributed inside the drum, and the machine stops, ending the operation with an emergency code. There is no need to be afraid. To continue washing, you need to open the door, unload the crumpled laundry and, after straightening it, load it back.
If turning on a washing machine is new to you and you haven’t encountered it yet, then this article is for you. First of all, you need to read the instructions or look them up on the Internet. If you purchased the machine secondhand, then ask the former owner if there were any difficulties with starting, perhaps there are some nuances.
Installing a washing machine
Unpack the electrical device and unscrew the shipping bolts. Their location is at the rear of the machine. Plastic plugs must be inserted into the resulting holes.
Now you can install the machine on a hard surface (no need to put anything under the device). Next, you need to adjust the legs so that the machine stands stable; to do this, you need to unscrew them to fix the desired height.
Preparing for launch
All modern models washing machines they differ little from each other in terms of launch. Before turning on the washing machine, check whether there is a power cord and whether the device is grounded. If everything is normal, then you can load laundry into the drum.
Each washing machine drum has its own weight category for which it is designed. Be careful, overloading may cause the crosspiece to fail. Most modern models have a function that notifies you if you have put more clothes than necessary.
After loading things, close the door. If you have a vertical drum, first close the door, and then the hatch. In a horizontal drum, close only the door.
The packaging of the powder should indicate the dose that needs to be poured into the compartment. It is important to stick to the dose, because if you pour in the powder, foam will appear, and if you do not add enough of it, the clothes may not be washed at all. To make sure you don't make a mistake, use a special measuring cup.
The powder tray has three sections:
- left – main department;
- average – designed for air conditioning;
- right – preliminary.
Powder tray
Basically, the compartments are located like this: on the left - for the main wash, next - for rinsing and pre-washing.
Now we need to supply the car with water. Most washing appliances are connected directly to the water supply, but some models have separate tanks. After completing this action, we connect the device to the network.
At this stage of time, there are the following types of washing:
- gentle wash;
- children's clothing;
- quick wash;
- washing everyday clothes.
As for fabrics, there are separate modes for the following types of fabrics:
- wool;
- cotton;
- synthetics.
Types of modes:
- Special regime: This function is mainly found in new models; it disinfects and protects white items with steam and helps remove stains. It should be described in more detail in your machine manual.
- Delicate wash: slow erasing and low rinsing speed. It’s good in that it prevents things from looking worn out, but it doesn’t wash very thoroughly. Suitable for delicate items.
- Light spin: First a quick wash, then a slow wash.
- Ordinary: fast rinsing and equally fast spinning.
Temperature detection
Temperature ranges from 30 to 95 degrees. Here are some recommendations for choosing a mode:
- The temperature is selected depending on how dirty the clothes are. If you just need to refresh, then choose 30-40 degrees.
- Synthetics wash perfectly in conditions of 40-60 degrees.
- Bed and bath linen and accessories require the highest temperature.
Spin intensity
The intensity is determined by the number of revolutions per minute. Naturally, the more efficient the spin is, the less water there is in things; when you take almost dry clothes out of the washing machine .
Don’t forget that fabrics that require more care should be washed at a lower intensity. It is generally better to wash silk and chiffon without the spin function.
Washing program
All information should be described in detail in your instructions. Expensive models are equipped with touch sensors, while simpler ones have a regular wheel. Now let’s start, to do this we find the “Start” button and press it.
When the washing process comes to an end, depending on your device, it will give a signal or a sound, or the button will flash that the wash has come to an end. We disconnect the device from the power supply, open the door and take out things.
First start
The first wash can be a test wash to check your washing machine for leaks. This will allow you to check if everything is connected correctly. If you suddenly find a leak, stop it immediately.
If the experiment is successful, then you can wash your clothes. This point is important because a leak can damage your device.
Tips that will be useful after purchasing a washing machine:
- If, after starting, your machine begins to make strange sounds, do not do anything yourself. Call the service, you should rightfully receive repairs under warranty or replace the defective one.
- The housing requires frequent wiping; use products that do not contain chlorine.
- The rubber seal becomes a source of dirt and must also be cleaned.
- Hand-held powders are absolutely not suitable for washing in an automatic washing machine; this powder may not only fail to wash the laundry, but also cause damage.
- You cannot overload the drum; read the instructions for the limit of your device.
- Check clothes for missing items before putting them in the machine.
- As soon as the wash is finished, do not rush to close the door, let it air out. If this is not done, an unpleasant odor and even mold may appear.
- Descale frequently.
Remaining powder in the compartment can also cause damage to the washing machine, so you should:
- Use a water softener that is specifically sold for this purpose.
- Be sure to wash the container after each wash.
- After washing, you need to let the tray dry inside; do not immediately close the door.
- Clean trays.
- The powder must be of high quality.
- If you resort to concentrates, then do not forget to rinse the machine.
For high-quality washing you will need the following components:
- A universal powder that is suitable for various types linen
- Powder containing bleach.
- There are various products for colored fabrics in stores.
- A product with a biological additive will remove the most difficult stains.
- Special powders that allow you to wash in cold water.
- Synthetic products.
- Reagents that allow you to wash white clothes.
How to prepare clothes for washing?
Clothes must have a label with instructions for washing. Always look at this information so as not to spoil things because something cannot be washed in hot water, or cannot be washed with bleach, or in general can only be washed by hand. Do not put items labeled with labels such as dry cleaning in the washing machine.
Organize items by color. Because one color can stain all your clothes. Sort into dark and light colors and denim items. Sort clothes into heavy and light ones. This will help the fabric look new for a long time. Heavy fabric includes jackets, fur coats, various bath accessories, sweaters, and cotton products.
To protect delicate clothing, it can be placed in the washing tray. But choose everything strictly according to color, maybe with a light fabric.
Separate clothes according to their stains; some heavy stains require separate preparation, such as greasy stains. Please note that at high temperatures, some stains are very difficult to remove, so it is highly undesirable to use it.
are popular among Russians for their successful price-quality combination. Italian washing machines are generously equipped with programs and modes - all for user convenience. To make “communication” with the device as convenient as possible, all washing modes in the Indesit washing machine are displayed on the control panel. Each wash option is labeled and indicated with an intuitive icon. Let's figure out what functions and programs are available in Indesit machines and what designations they have.
Why do you need instructions?
Regardless of the model and brand of SMA, the first thing the user should do is take the time to read the instructions. This is where you can find answers to most questions. Most often they look there to understand the control panel. Subsequently, having remembered the designations and essence of the proposed programs, washing machine owners can easily and quickly select the desired options.
Sign system from Indesit
The Italian manufacturer has taken care of maximum control accessibility. The icons used are clear to the user. Each one is signed verbally and numbered. Designations:
- Cotton - cotton box or T-shirt.
- Delicate wash - flower.
- Curtains - image of curtains.
- Wood is an economical version.
Let's take a closer look at what options are offered by SMA from Indesit.
What does Indesit offer?
Mode is a process characterized by certain conditions. The temperature, drum rotation speed, time and goal vary. A program is a specific order of actions, which, differing in washing conditions, can consist of several modes.
Basic
- Cotton. T-shirt or cotton box drawn. The user can select options with different temperatures and durations:
- 90–95 degrees is a good option if you need to wash stained kitchen towels. The drum is fully loaded. And the cycle time is almost 3 hours.
- 60 degrees. With intensive washing, the process is shorter, since the soaking step is eliminated. Duration is reduced to 2.5 hours. This option is chosen for heavily soiled white items - tablecloths, towels, bed linen.
- 40 degrees. Recommended for colored products. Duration - about 2.5 hours.
- Synthetics. A flask with temperature indication is shown. There are two options:
- 60 °C - 1 hour 25 min.
- 40 °C - gentle version, lasting 1 hour 11 minutes. Loading - 50%. This is usually 2.5–3.5 kg, depending on the model.
- Wool. A skein of thread is drawn. For wool and cashmere items. Duration - 55 min. Temperature - 40 °C. Spin speed is reduced.
- Silk. In the picture there is a T-shirt. For curtains made of thin fabrics, for viscose and underwear. They are washed at 30°C for 55 minutes. Load the drum by about 20% - up to 1–1.5 kg. There is no spin.
Some models may contain separate modes, without an emphasis on fabric. Washing available:
- Preliminary. Use instead of soaking. Gently rotate in slightly warm (30 °C) water.
- Daily (everyday) - standard program for quickly washing lightly soiled items.
- Intense. For cotton and linen. Hot water - up to 95 °C. This is an analogue of “cotton 90 °C”.
- Delicate - similar to “wool”. You can wash completely different fabrics that have the same common feature- special requirements for process conditions. Wool, organza, lycra and other delicate materials are washed at 40 degrees.
Additional
They are chosen for specific items - taking into account the fabric and degree of contamination:
- Jeans. The icon matches the name. Created specifically for denim products. Wash at 40 degrees. Loading - up to 2.5 kg. Drum speed is reduced.
- Quick wash mode. The picture is a clock. The express version allows you to wash things in a quarter of an hour. Loading - about one and a half kg. Temperature - 30 °C.
- Shoes. The picture shows a sneaker. Designed for sports shoes - sneakers, suede sneakers. Wash in lukewarm water, two pairs at a time. Cycle duration - 50 min.
- Sportswear. There are models with two options - regular and intensive. The water is heated to 30 °C. Time - 1 hour 20 minutes.
SMA "Indesit" also has special functions:
- additional rinse - intuitive designation - variations on the theme of drops and a basin of water;
- spin - a pattern in the form of a twisted spiral;
- Eco Time - reduces time and water consumption. Compatible with synthetics and cotton 40.
- easy ironing - iron drawn;
- delayed start - icon with a clock.
What buttons and selectors are there?
Any Indesit SMA has the following elements on the control panel:
- Program switch. There are icons on the panel, duplicated with pictures. The consumer turns the selector to select the desired option.
- Temperature switch. If the user selects a specific program, the temperature is set automatically. But thanks to the selector, you can adjust the water heating.
- Speed switch. The rotation speed of the drum can also be changed - in any direction.
- Start/stop or on/off button. Activates and deactivates the machine. Near the button there is an LED indicating the state of the device.
Also on Indesit machines, depending on the model, there are additional buttons:
- 50% load. It is pressed if you need to wash several items. Saving water and electricity.
- Reducing the spin speed. Use for delicate fabrics.
- Super rinse. For thorough rinsing.
- Cold wash. For delicate materials and not very dirty things.
- Disabling spin.
How to set the desired mode?
The selection is made using the programmer knob. There are inscriptions and icons around the selector switch. On older models there are no verbal designations - only icons, hence the problems with selection. It happens that the owners of the machines do not understand the images, then they need instructions to decipher the symbols. In the new models, the manufacturer took this omission into account - all icons are duplicated with words.
Before you set the mode, you need to sort the things that you are going to wash. Evaluate them by type of fabric, color, degree of soiling. Taking these positions into account, a decision is made: choose a ready-made program or customize your own. If preference falls on the second option, then the user selects:
- temperature;
- duration of the process;
- rotational speed.
Whether a ready-made program is included or your own is being configured, the user can add additionally:
- soak;
- rinsing;
- light ironing;
- spin
The process can be postponed for a certain time - depending on the duration of the timer. Typically, the maximum delayed start time is 24 hours. Descriptions of the modes can be read in the instructions.
Features of the work of SMA "Indesit"
When using Indesit washing machines, follow these rules:
- Please note the maximum permissible drum load.
- Sort your laundry by color, type of fabric, color fastness and presence of decor (embroidery, beads, rhinestones, etc.). The presence of decorative decorations is a reason to use special bags.
- Read the labels on things - what is allowed and what is prohibited for a particular product.
- Check your pockets - this will prevent damage to the SMA.
- Turn sweaters, shirts and other clothes inside out - this will improve the quality of washing.
- It is forbidden to wash many large items at the same time - so as not to disturb the balancing of the drum.
- When pressing the “start” button, make sure that the device is turned on.
- When choosing a mode, turn the selector to the desired position. If necessary, adjust the process parameters using special switches. Having adjusted software settings, start the device.
What is prohibited?
Users of the Indesit SMA should know which actions should be avoided and which are completely prohibited:
- It is not recommended to load several large items into the machine at the same time. It is advisable to put one or two large items and any small items in addition.
- Do not use powders for hand washing - this may result in increased foaming.
Special modes in popular Indesit models
- WG1035txc. A distinctive feature of this modification is the presence of additional settings for each main program. For example, not just “synthetics”, but several options - with fabric softening, anti-shedding and for durable colored products. Additionally, automatic addition of softening agents is installed.
- IWDC 6105. There is a non-standard “light sports” option - for washing lightly soiled sportswear for fitness, yoga or swimming. There is a “quick dry wash” - it quickly washes and dries things. Half load. Ready time - 15 minutes.
- WISL 105. Only one additional option - “everyday wash at 30 °C”. Applicable to synthetics with minor stains. Allows you to save water and electricity. It is recommended to use liquid detergents.
- WISL 102. In addition to “everyday care 30 degrees”, there is also “light ironing” - its activation depends on the tolerance of the selected program, load and temperature.
- WIT 60. Budget version without additional options. But there is a “water stop” function.
- WIUN 102. There is “daily washing of synthetics” at 30 degrees.
Useful video:
Distinctive feature model range"Indesit" is a conservative control panel. It is easy to understand, since almost every icon is duplicated with an inscription. Simple operation is the key to “mutual understanding” between the user and the technology.
The new washing machine was delivered, unpacked, installed on its workplace and connected to water supply. Do you really want to launch it as soon as possible and see it in action? Experts recommend not to rush, since its performance and durability depend on the first turn on and the initial wash. Haste and incorrect actions of the newly made owner can not only harm, but even destroy an expensive unit. must be carried out in accordance with the manufacturer's recommendations. Therefore, it is important to carefully read the attached instructions.
Preliminary preparation of the washing machine
Before the first start, it must be carried out full installation equipment: water supply and sewerage hoses are connected, the device is leveled, the shipping bolts that hold the drum during loading and transportation are removed.
Before turning on for the first time, it is worth checking the readiness. It won’t take much time, but it will protect the owner from surprises that may arise if something was missed in a hurry.
Checking readiness
Before turning on and starting the washing machine for the first time, it is recommended:
- Read the operating instructions carefully. In this case, special attention should be paid to the section for controlling washing modes. Mismanagement by the user, may affect the performance of the electronic unit of the device.
- Check the connection of the machine hoses: rubber for water supply (fill) and corrugated for draining into the sewer (drain). It is better to secure the corrugated hose, since if water is actively drained from the washing machine, it can fall out and cause a flood.
- Check the rear wall of the device for the presence of transport bolts. They secure the internal parts of the machine and the drum for safety during tilting and transportation. If the bolts are in place, they must be removed and the holes closed with rubber covers, which are usually included with the machine. In most cases, the manufacturer provides 4 shipping bolts.
- Open the water shut-off valve on the inlet hose.
- Check to see if any remaining adhesive tape used to secure the parts has been removed from the front, back and side walls of the machine.
- Open and inspect the drum of the washing machine to see if there is any debris or any parts in it.
These are mandatory steps that must be carried out before starting the washing machine for the first time.
First wash
Manufacturers of washing machines and experts recommend doing the first wash in vain - without adding laundry and staying near the machine the entire time of washing.
Instructions for starting the startup launch:
What should you pay special attention to?
The first launch of washing machines from LG, Bosch, Candy, Indesit, Hotpoint Ariston, Samsung, Haier, Vestel, Beko and devices from other manufacturers is practically no different.
In all cases of violation of the normal operating mode and washing, you should call a specialist or look for the cause of the malfunction yourself.
If, when starting up the washing machine for the first time, the user notices knocking, grinding or other strange sounds, without delay, you should call a specialist from a repair shop or service center. You cannot wash until the problem is fixed, even if the problem does not seem serious.
Recommendations for the first wash without laundry are based on the fact that most of the surfaces of the drum and drains are most often contaminated with technical liquids and oils, the use of which is necessary during assembly at the manufacturer. In addition, these same parts can retain unpleasant odors for a long time. The main thing, with such an idle wash, is to check whether the parts and components of the new machine are working properly, whether the water supply and drainage system is sealed.
First wash products
Specialty stores household appliances offer an inexpensive tool for starting up a washing machine for the first time. It contains products that destroy all technical odors, dirt and impurities. After using this product, a pleasant smell remains in the washing drum for a long time. This product is added to the powder container during the first wash.
To make your washing machine last a long time, you need to listen to simple tips:
- do not overload the machine with excess laundry;
- separate white laundry from colored laundry and do not wash them together;
- check the pockets of loaded items, especially for the presence of metal objects;
- To soften water, use water softeners and conditioners when washing;
- clean the drain hose filter from small debris;
- Wipe the machine panel and drum door with special substances that do not contain chlorine or abrasives.
Recommendations for the first launch of a washing machine from Bosch, Candy, LG, Indesit, Hotpoint Ariston, Samsung, Haier, Vestel, Beko and other companies, as well as their further operation, are practically no different. Following these simple recommendations will help maintain the longevity of your household appliances without repairs.
